Skip to content

LWS47XX Zenith Waterborne Powder Glaze 3.78L

Original price $20.25 - Original price $20.25
Original price
$20.25
$20.25 - $20.25
Current price $20.25

Sold by the Litre.   Order as 4L(Gallon)

Zenith™ Waterborne Powder Glazes are unique glazing products used for creating antique looks and other special effects. They are
designed to be applied over a sealed and sanded surface, and then either wiped off while still wet, or removed with a Scotchbrite™
pad (or similar) after the glaze has dried to a powder. These glazes must be top coated. They are fast drying, have very little odor,
and clean up with water. Choose from four popular ready-mix colors or an unlimited color palette available with the Color Choice™
program. This product is designed for professional use only.
1. PRODUCTS • LWS4710-Black LWS4712-White
• LWS4711-Burnt Sienna LWS4713-Van Dyke Brown
2. MIXING RATIO
Before using, mix at slow to moderate speed until there is
no material on the bottom of the container. If tinting,
colorants must be mixed in with a shaker or mechanical
agitation such as an air mixer or drill.
3. SHELF LIFE @ 77°F (25°C) • 24 months from manufacturing date
4. CLEAN UP • Clean equipment with warm water. If coating has dried,
acetone may be required to remove dried film. Keep
container closed when not in use to avoid skinning
5. SURFACE PREPARATION • Surface must be clean and dust free with a moisture
content of 6-8% prior to finishing. Remove all dust,
dirt, wax and wood marks. Proper sanding and
preparation of the wood is critical to achieving
consistent results.
• On new wood, finish sand surface with 150-180 grit
sandpaper
• On previously finished wood, remove all old paint or
varnish and follow new wood procedure.
6. COMPANION PRODUCTS • Zenith Waterborne Precatalyzed Lacquer
• Zenith Waterborne Conversion Varnish
• Can also be used with Valspar’s solvent borne Lacquers,
Precatalyzed Lacquers and Conversion Varnishes
7. TECH NOTES • No thinning is recommended.
8. SUBSTRATES • Commonly used furniture and cabinetry woods
• MDF/HDF
NOTE: Not to be used on exterior applications
10. APPLICATION • Ready to spray. May be used as a self-seal topcoat. No
thinning is recommended.
• Do not apply more than 4 coats at 3-4 wet mils per coat
when used as a self-seal system. Maximum film thickness of
the total coating system must not exceed 4 dry mils.
11. FLASH / DRY TIMES
AIR DRY @ 77°F (25°C)
12. FORCE DRY
Flash 5 Minutes
Bake 5 Minutes @ 130°F
Cool Down 10 Minutes ambient
Stack
13. GUN SET UP
Gravity Feed 1.6 mm - 1.8 mm
Siphon Feed 1.8 mm – 2.0 mm
Airless 10 – 15 thousandths
Air-Assisted Airless 11 – 15 thousandths
AIR PRESSURES
Gravity Feed 30-35 psi (2.0-2.4 bar)
Siphon Feed 35-40 psi (2.4-2.8 bar)
Air-Assisted Airless 5-10 psi (0.3-0.7 bar)
See spray gun manufacturer data for more information
14. PHYSICAL DATA
Viscosity N/A
Weight Solids % 20.2-24.09%
Volume Solids % 9.1-10.55%
Actual VOC .13-.2 lbs/gal of Product
VOC Ratio (lb.voc/lb.solids) .06-.09 (lbVOC/lb solid)¹
Regulatory VOC
(less water and exempt solvents) 137.43-191.25g/l
Weight Per Gallon 9.5-9.82 lbs/gal¹
Flash Point 299ºF Closed Cup
Theoretical Coverage 146-169 ft/gal @ 1 mil dry
VHAP (lb.HAP/lb.solids) 0.0 lb VHAP/lb solid
Photochemically Reactive No
Coating Category Pigmented
Dry to touch 15 Minutes
Flash between coats 30 Minutes
To Stack